cosi Documentation

cosi - Divide by cos(incidence angle) from backplane
This program divides the core of the input file by the cosine of the
incidence angle, which is obtained from the INCIDENCE_ANGLE backplane
in the cube.  The INCMAX and EMAMAX parameters allow specifying maximum
incidence angle and emission angle values.  If either the incidence
angle or emission angle (or both) exceed the specified maximum value,
then the entire output spectrum at the corresponding spatial location
is set to all NULL values.  Both the INCIDENCE_ANGLE and EMISSION_ANGLE
backplanes must exist in the input file.

PROGRAMMER: Jim Torson, U.S.G.S., Flagstaff, AZ

Input cube file name
  (default extension is .cub)

NONE

Input subcube specifier

--

Output cube file name
  (default extension is .cub)

NONE

Max incidence angle (degrees)

89.0

Max emission angle (degrees)

89.0

Output pixel type
 NULL = input type
    1 = 8 bit
    2 = 16 bit
    3 = 32 bit

--

Output min/max data range

--

User comment

" "

ADDITIONAL NOTES:

Parm	Description
FROM	Input cube file name. If the file extension is omitted, then ".cub" will be assumed.
SFROM	SFROM specifies the subcube using a single string for all three dimensions of the cube. The order of the three dimensions is always "samples:lines:bands". If a dimension is left blank, all the data for that dimension is selected. The default value of NULL for SFROM selects the entire cube. Any application below can be used for any dimension. To select specific data from any dimension: "10-100(3):11,12,15-20:1-10(2)" = This example will select every third sample starting with sample 10 thru 100. It selects lines 11 and 12, and 15-20. It selects every other band, starting with band 1 thru 10. There are special characters that can be used for selecting a subcube efficiently, such as "*","#", and "~". For examples type "help sfrom" in TAE. **NOTE** For more examples and explanation of the many features of the SFROM parameter, tutor the sfrom.pdf or refer to Introduction To ISIS, Section 6, of the ISIS User's Manual **
TO	Output cube file name. If the file extension is omitted, then ".cub" will be assumed.
OTYPE	Output pixel data type. Permitted values are: NULL = output type is same as input file pixel type 1 = 8-bit (integer with type conversion parameters) 2 = 16-bit (integer with type conversion parameters) 3 = 32-bit (floating point) When processed data are being written back into the input file, the output pixel type must be the same as the existing pixel type in the input file.
INCMAX	Maximum permitted incidence angle (degrees). If the incidence angle at a spatial location exceeds the specified value (or is not a valid value), then the entire spectrum at the corresponding location in the output file is set to all NULL values.
EMAMAX	Maximum permitted emission angle (degrees). If the emission angle at a spatial location exceeds the specified value (or is not a valid value), then the entire spectrum at the corresponding location in the output file is set to all NULL values.
ORANGE	Output pixel data range. If ORANGE is NULL, then the CORE_BASE and CORE_MULTIPLIER in the output file will be set to represent the same range of data as the input file. If OTYPE=1 (8-bit) or OTYPE=2 (16-bit), then the CORE_BASE and CORE_MULTIPLIER in the output file will be set to values that allow representing the specified range of output values. Output values outside this range will be stored as a special "representation saturation" value. The ORANGE parameter is ignored if OTYPE=3 (32-bit) since the CORE_BASE and CORE_MULTIPLIER are not applicable to floating point pixel values. **NOTE** For a more detailed explanation of ORANGE, tutor the orange.pdf.
USERNOTE	Comment from the user. This will be recorded in the ISIS session log file and also in the History entry that is put into the History object of the output file.